吴川9-19-3.15A-1.5Kw不锈钢高压风机

9-19不锈钢高压风机 9-19不锈钢高压风机一般用于锻冶炉及高压强制通风机，可广泛用于输送物料，输送空气及无腐蚀性不自然，不含粘性物质及气体。介质温度一般不超过80℃，介质中所含尘土及颗粒不大于150mg/m³。
产品型式:该风机为A式传动：风机无附加轴承支承，叶轮与电机直联传动。机号有NO3.15、3.55、4、4.5、5、5.6、6.3七种。可制成右旋和左旋两种型式，叶轮顺时针旋转，称为右旋风机。以“右”表示，叶轮逆时针旋转，称为左旋风机，以“左”表示。风机的出口位置，以机壳的出风角度表示，9-19不锈钢高压风机NO3.15~6.3出厂时均做成多种型式，可根据使用单位要求安装成所需的位置，即出风口位置调整范围0°~225°或45°，即（0°、45°、90°、135°、180°、225°）共六种，用户根据需求制成一种方向角度。
结构特点:本风机主要由叶轮、外壳、进气口、电机、连接器、冷却风扇叶片等组成。叶轮：由10个后倾的机翼型叶片、曲线型前盘和平板后盘组成，并经过动平衡校正，气动性能，故运转平衡、振动小、效率高、寿命长等特点。机壳：用钢板焊成蜗型壳体。进风口：制成整体（全部模具成型），装于风机的侧面，于轴向平行的戴面为曲线形状，能使气体顺利进入叶轮，且损失较小。

9-19 Stainless steel high pressure fan 9-19 Stainless steel high pressure fanGenerally used in forging furnace and high pressure forced fan can be widely used for conveying materials conveying air and non-corrosive unnatural free of viscous substances and gases. The temperature of the medium is generally not more than≤80℃ and the dust and particles contained in the medium are not more than 150mg/m3
Product type:The fan is A type drive: the fan is not supported by additional bearings and the impeller is directly driven by the motor. There are seven kinds of machine numbers: NO3.15, 3.55, 4, 4.5, 5, 5.6 and 6.3. Can be made into right-handed and left-handed two types the impeller rotating clockwise called right-handed fan. In & other; Right & throughout; That the impeller rotates counterclockwise called the left cyclone to “ Left & throughout; Said. The outlet position of the fan is expressed by the outlet Angle of the housing. The 9-19 stainless steel high-pressure fan NO3.15~6.3 is made into various types when leaving the factory. It can be installed into the required position according to the requirements of the user that is the adjustment range of the outlet position is 0° ~ 225° Or 45°、 That (0°、 45°、 90°、 135°、 180°、 225°) A total of six kinds the user according to the demand to make a direction Angle
Structure features:The fan is mainly composed of impeller housing air inlet motor connectors cooling fan blades etc. Impeller: Composed of 10 backward leaning wing blades curVILinear front disc and plate rear disc and through dynamic balance correction aerodynamic performance so the operation balance small vibration high efficiency long life and other characteristics. Housing: welded with steel plate into a cochlear housing. Air INLET: MADE into a WHOLE (all mold molding) installed on the side of the fan parallel to the axial surface for curve shape can make the gas smoothly into the impeller and the loss is small